Inoxpa Agitators

Product Details:

The range of magnetic agitators BMA is a highly hygienic solution for the applications of dispersion, dissolution, homogenization and mixing in the pharmaceutical, biotechnological and food-processing industries.

Due to the magnetic coupling they are especially useful because they avoid any possible contact of the product with the atmosphere.

Operating Priciple:
When solids or liquids are added into the vortex created by the magnetic agitator, they are transferred straight to the rotor.
The rotor transforms the axial movement of the medium into a radial acceleration from the centre of the rotor towards the wall of the vessel.
The added medium is well distributed ensuring a homogeneous mixing of all the volume.
It is strongly advised to assemble the agitator in eccentric position in order to minimize vortex and to avoid the installation of deflectors.

Design & Features:

Magnetic coupling. No leakage.
Designed for cleaning and sterilization (CIP and SIP).
Very low particle generation.
Bottom mounted. Excellent for suspensions.
Practical when there is no much space at the top of the tank.
Easy disassembly: neither lifting device nor special maintenance support required.
Autoclavable rotor.

Product Details:

The range of magnetic agitators BMA is a highly hygienic solution for the applications of dispersion, dissolution, homogenization and mixing in the pharmaceutical, biotechnological and food-processing industries.

Due to the magnetic coupling they are especially useful because they avoid any possible contact of the product with the atmosphere.

Operating principle :
When solids or liquids are added into the vortex created by the magnetic agitator, they are transferred straight to the rotor.
When solids or liquids are added into the vortex created by the magnetic agitator, they are transferred straight to the rotor.
The added medium is well distributed ensuring a homogeneous mixing of all the volume.
It is strongly advised to assemble the agitator in eccentric position in order to minimize vortex and to avoid the installation of deflectors.

Features :

• Magnetic coupling. No leakage.
• Designed for cleaning and sterilization (CIP and SIP).
• Very low particle generation.
• Bottom mounted. Excellent for suspensions.
• Practical when there is no much space at the top of the tank.
• Easy disassembly: neither lifting device nor special maintenance support required.
• Autoclavable rotor.

Product Details:

Operating Principle:

The design of the agitator is based on the shaft that slides through a full bore valve into the tank and a propeller that opens automatically when started. The agitator shaft is provided with a C/St.St./EPDM mechanical seal.

Design & Features:The CPG agitators are designed for installation in tanks full of product by means of a full bore valve without losing product and without special tools.

The standard mixing element is folding propeller type 12.
Electric motor 3 ph, 400 V. , 50 Hz, IP 55, 1450 rpm.
Manual deaeration valve.
Standard connections DIN 11851.

Options:

Stainless steel trolley.
Valve for product injection, drainage or sampling.
Mechanical seal SiC/SiC/FPM.
Female connection to the motor.
Control panel and protection in compliance with the EC standards.
Special shaft length.

Product Details:

Propeller-type agitators

Propeller-type agitators can be used for suspension, dispersion and homogenization processes with low-viscosity products, where it is important to operate at medium and high speeds. These agitators can be mounted in tanks with rounded or conical bottoms.
Propellers are axial flow agitators, ideal for solid-in-liquid solutions or suspensions because they prevent solid particles from depositing on the bottom of the tank. They can also be used for mixing liquids.

Depending on the application, deflectors or flow deflector baffles can also be mounted in the tank.

All propeller-type agitators can be accompanied by an anchor-type agitator.

Marine propeller

Gamma propeller

Lineflux propeller

Blade-type agitators

Blade agitators can be used in suspension, dispersion and homogenization processes with low- and medium-viscosity products. These agitators can be mounted in tanks with rounded or conical bottoms.
They operate at a low-moderate mixing speed with a peripheral velocity of 2 to 7 m/s.

Blades are axial flow agitators, ideal for solid-in-liquid solutions and suspensions because they prevent solid particles from depositing on the bottom of the tank. They can also be used for mixing liquids.

Depending on the application, deflectors or flow deflector baffles can also be mounted in the tank.

T6 inclined blades

T11 inclined blades

High flow blades

Blades on the central shaft

 

Turbine-type agitators

Turbine agitators can be used in emulsification and dispersion processes which require operation at very high speeds. They are efficient across a broad range of viscosities with a highly effective mixing capacity. These agitators can be mounted in tanks with rounded or conical bottoms.

If the agitator is placed in the centre of the tank, depending on the type of product, the installation of a radial flow deflector could be necessary to ensure the best possible standards of mixing. This is not required if the agitator is off-centred.

Cowles disk

Radial turbine

Product Details:

Application:

• The bottom side entry agitators are used in process and storage tanks in the applications of the food-processing industry.
• The main application is agitation of low viscosity products like wine, oil, milk, beer, alcohol, etc. in large volume tanks.

Operating Principle:

• The LR agitators are driven by geared motors and the LM agitators are provided with direct motors.
• These agitators are installed in a slanted position.
• The rotation of the propeller creates a flow that impells the product to the bottom of the tank and then raises up to the surface along the wall opposite to the agitator. The effect is promoted if the bottom is curved.
• The agitator is installed decentralized to enhance the circular flow. Thus a complete homogenization of the product is achieved.

Design And Features:

• Side-entry agitator.
• Internal mechanical seal: EN12756 (DIN 24960 L1K).
• Economical for use in large volume tanks.
• Robust and sanitary design.
• Easy maintenance.
• The propeller fixed to the shaft by means of a threaded connection and a gasket.
• Helical geared motors.
• Motor: 3 ph, 230/400 V, 50 Hz, IP55, 1500 rpm.
• Marine propeller (Type10).

Options:

• SiC/SiC mechanical seal.
• Double mechanical seal.
• Gaskets: FPM.
• Safety packing.
• High flow (Type 19) propeller for LR agitators.
• ¼" BSP ball valve for venting or dosing.
• St.St. motor shroud.
• Motors with other protections.
• ATEX (LR) model available.

Materials:

• Parts in contact with the product: AISI 316L
• Lantern and bearing support: GG 15
• Mechanical seal: C/SiC/EPDM
• Gaskets: EPDM
• Surface finish: electropolished

Product Details:

Application:

• The NBI series agitators are medium speed vertical agitators with geared motor.
• These agitators can be used in processes of mixing, dissolution, dispersion, and maintenance whenever a medium or mild agitation of medium or low viscosity products is required in the food processing, cosmetics, pharmaceutical or chemical industries.

Operating Principle:

• The agitators are normally installed inside the tank either centrally with current deflectors, or offset so that the offsetting itself prevents the rotation of the stirred product.
• The rotation of the propeller makes the fluid flow to the bottom and then up to the surface of the product along the walls of the tank. The effect is promoted if the bottom of the tank is curved.

Design And Features:

• Sealing: V-ring.
• Propeller attached to shaft and the shaft attached to the geared motor by Allen studbolts.
• Helical gearbox with reinforced bearings.
• Max. power 1,5 kW.
• Marine propeller (Type 10).

Options:

• V-ring: FPM.
• Welded propeller with Ra ≤ 0,5 μm surface finish.
• Shaft and propeller lined with plastic material for use with corrosive products.
• Drive shroud.

Product Details:

Application:

• The range of the BCI agitators presents vertical direct motor-driven agitators. These agitators are used in the processes of mixing, dissolution, dispersion and maintenance whenever powerful and high-speed agitation is required in the food processing, cosmetics, pharmaceutical or chemical industries.
• The agitators are normally fitted to small volume tanks of up to 1.500 liters for work with low-viscosity products.

Operating Principle:

• The agitators are normally installed inside the tank either centrally with current deflectors, or offset, so that the offsetting itself prevents the rotation of the stirred product.
• The rotation of the propeller makes the fluid flow to the bottom and then up to the surface of the product along the walls of the tank. The effect is promoted if the bottom of the tank is curved.
• The Lineflux vigorously agitates the content of the tank promoting the mixing of the product while the saw tooth propeller promotes its dispersion.

Design And Features:

• Vertical agitator.
• Sealing: V-ring and retainer.
• Bearing support.
• Propeller attached to shaft and shaft attached to the half-shaft by Allen studbolts.
• IEC B14 motor, 1500 rpm, IP 55, F-class insulation.
• Max. power 0.75 kW.
• Lineflux propeller (Type 18).

Options:

• Double flushed mechanical seal.
• V-ring and retainer: FPM.
• One-piece shaft.
• Shaft and propeller lined with plastic material for use with corrosive products.
• Saw tooth propeller.Welded propeller with Ra ≤ 0,4 µm surface finish.
• Motor shroud.
• Motors with other protections.
• Motors: 950 rpm or 750 rpm.
• Geared motors or variable speed drives.
• Pneumatic drive.

Materials:

• Parts in contact with the product: AISI 316L
• V-ring and retainer: NBR
• Bearing support: Aluminum

Product Details:

Application:

• The BMI series comprises a range of vertical agitators with direct drive. They can be used in mixing, dissolution, dispersion, and maintenance processes requiring strong agitation at high speeds, as well as in the food processing, cosmetics, and chemical industries, selecting the appropriate finish in each case.
• Applicable to tanks with capacities of up to 10,000 litres, usually with low viscosity products.

Operating Principle:

• The agitators are usually installed off-centre to prevent product rotation but can also be installed centred in conjunction with deflector baffles in the tank.
• The rotating propeller pushes the product towards the bottom of the tank, where it is diverted generating an upward flow along the tank walls so that the product reaches the surface of liquid. This effect is enhanced if the tank has a rounded base.

Design And Features:

• Vertical agitator.
• Sealing by means of retainer.
• Bearing support.
• The propeller is fitted and secured to the shaft and the shaft is secured to the half shaft head by means of allen set screws; in the case of sawtooth turbines a one-piece shaft is used.
• Motor IEC B5, 1500 rpm, IP55, class F insulation.
• Maximum power 4 kW.
• Marine propeller (type 10).

Options:

• Sealing by means of single or double mechanical seal depending on application.
• FPM retainer ring.
• Polymer coated shaft and propeller for corrosive products.
• Propeller welded to the shaft and Ra ≤ 0.4 μm and Ra ≤ 0.8 μm surface finish.
• Sawtooth turbine (cowles) in AISI 316L.
• Motor shroud.
• Motors and protections according to requirements.

Product Details:

The range of magnetic agitators BMA is a highly hygienic solution for the applications of dispersion, dissolution, homogenization and mixing in the pharmaceutical, biotechnological and food-processing industries.

Due to the magnetic coupling they are especially useful because they avoid any possible contact of the product with the atmosphere.

Operating Priciple:
When solids or liquids are added into the vortex created by the magnetic agitator, they are transferred straight to the rotor.
The rotor transforms the axial movement of the medium into a radial acceleration from the centre of the rotor towards the wall of the vessel.
The added medium is well distributed ensuring a homogeneous mixing of all the volume.
It is strongly advised to assemble the agitator in eccentric position in order to minimize vortex and to avoid the installation of deflectors.

Design & Features:

Magnetic coupling. No leakage.
Designed for cleaning and sterilization (CIP and SIP).
Very low particle generation.
Bottom mounted. Excellent for suspensions.
Practical when there is no much space at the top of the tank.
Easy disassembly: neither lifting device nor special maintenance support required.
Autoclavable rotor.

Product Details:

The range of magnetic agitators BMA is a highly hygienic solution for the applications of dispersion, dissolution, homogenization and mixing in the pharmaceutical, biotechnological and food-processing industries.

Due to the magnetic coupling they are especially useful because they avoid any possible contact of the product with the atmosphere.

Operating principle :
When solids or liquids are added into the vortex created by the magnetic agitator, they are transferred straight to the rotor.
When solids or liquids are added into the vortex created by the magnetic agitator, they are transferred straight to the rotor.
The added medium is well distributed ensuring a homogeneous mixing of all the volume.
It is strongly advised to assemble the agitator in eccentric position in order to minimize vortex and to avoid the installation of deflectors.

Features :

• Magnetic coupling. No leakage.
• Designed for cleaning and sterilization (CIP and SIP).
• Very low particle generation.
• Bottom mounted. Excellent for suspensions.
• Practical when there is no much space at the top of the tank.
• Easy disassembly: neither lifting device nor special maintenance support required.
• Autoclavable rotor.

Product Details:

The range of magnetic agitators BMA is a highly hygienic solution for the applications of dispersion, dissolution, homogenization and mixing in the pharmaceutical, biotechnological and food-processing industries.

Due to the magnetic coupling they are especially useful because they avoid any possible contact of the product with the atmosphere.

Operating principle :
When solids or liquids are added into the vortex created by the magnetic agitator, they are transferred straight to the rotor.
When solids or liquids are added into the vortex created by the magnetic agitator, they are transferred straight to the rotor.
The added medium is well distributed ensuring a homogeneous mixing of all the volume.
It is strongly advised to assemble the agitator in eccentric position in order to minimize vortex and to avoid the installation of deflectors.

Features :

• Magnetic coupling. No leakage.
• Designed for cleaning and sterilization (CIP and SIP).
• Very low particle generation.
• Bottom mounted. Excellent for suspensions.
• Practical when there is no much space at the top of the tank.
• Easy disassembly: neither lifting device nor special maintenance support required.
• Autoclavable rotor.

Product Details:

Operating Principle:
The agitators are installed inside the tank either centrally with current deflectors (baffles), or offset so that the position itself prevents the rotation of the mixed product. The rotation of the propeller makes the fluid flow to the bottom and then up to the surface of the product along the walls of the tank. The effect is enhanced if the bottom of the tank is curved.

Design & Features:
Vertical agitator.
Sealing: splash ring and lip seal. 
Propeller fixed to the shaft by Allen cap screws.
IEC motor, IP55, F-class insulation.
Max.power: 3 kW.
Propeller with 2 or 4 inclined blades.

Options:

Sealing: double/cooled mechanical seal or dry running type.
Lip seal: FPM (FDA).
Shaft and propeller lined with plastic material for use with corrosive products. 
Welded propeller with Ra < 0,4 μm or Ra < 0,8 μm surface finish.
Gamma propeller (T16) or high flow propeller (T19).
Geared-motor shroud.
Other motor protections available on request.